Issue 50

I. G. F. Silva et alii, Frattura ed Integrità Strutturale, 50 (2019) 46-53; DOI: 10.3221/IGF-ESIS.50.06 53 [3] Heckmann, K., Sievers, J. (2018). Leak-before-break analyses of PWR and BWR piping concerning size effects. Nuclear Engineering and Design, 326, pp. 383-391. DOI: 10.1016/j.nucengdes.2017.11.027. [4] Deschanels, H., Gilles, P., Kayser, Y., Pignol, M., Lacroix, R. (2017). Improvement of Leak-Before-Break Methodology for Sodium Fast Reactors. SMiRT 24, Busan, Korea. [5] Liu, J., Wang, Y. (2017). Leak Before Break (LBB) Technology and Application in China Experimental Fast Reactor (CEFR). Mechanics and Materials Science, pp. 29-36. DOI: 10.1142/9789813228177_0004. [6] United States Atomic Energy Commission (1971). 10 CFR Part 50 - Appendix A - General Design Criteria for Nuclear Power Plants. [7] IAEA (1993). Applicability of the Leak Before Break Concept, IAEA, VIENNA, ISSN 1011-4289. [8] NUREG-1061 (1984). Report of the U.S Nuclear Regulatory Commission Piping Review Committee, Evaluation of Potential for Pipe Breaks, Volume 3. USNRC. [9] NUREG-0800-SRP 3.6.3 (1987). Leak-Before-Break Evaluation Procedures. USNRC. [10] Maneschy, J. E., Miranda, C. A. J. (2014). Fracture Mechanics in Nuclear Industry. Lithos (in Portuguese). [11] ASME (2013). ASME Boiler and Pressure Vessel Code, Section II, Part A, Ferrous Materials Specifications. [12] Norris, D. M., Chexal, B. (1987). PICEP: Pipe Crack Evaluation Program. EPRI NP-3596-SR, Revision 1. [13] Jong, R. P. (2004). Structural Integrity Assessment of Cracked PWR Piping Systems. M.Sc. Dissertation, Nuclear Technology Program, University of São Paulo (in Portuguese). [14] Koyama, K.; Muroya, I.; Tanaka, T.; Nakamura, T. (1999). Low Alloy Steel Piping Test for Fracture Criteria of Leak Before Break. Nuclear Engineering and Design, 191, pp. 147-156. [15] Miura, N. (1999). Approximate Evaluation Method for Ductile Fracture Analysis of a Circumferentially Through-Wall- Cracked Pipe Subjected to Combined Bending and Tension. Nuclear Engineering and Design, 191, pp. 177-194. [16] Zahoor, A. (1989). Ductile Fracture Handbook. NP-6301-D Research Project, Electronic Power Research Institute. N OMENCLATURE E Young’s modulus σ 0 Yield strength σ u Tensile strength ε 0 Strain for σ 0 α Strain hardening coefficient (parameter of Ramberg-Osgood’s law) n Strain hardening exponent (parameter of Ramberg-Osgood’s law) J IC J-Integral associated with the beginning of crack growth C Constant of the J-R curve m Exponent of the J-R curve L Q Leakage crack size J 1 Applied J-Integral for Case 1 J 2 Applied J-Integral for Case 2 L cr Critical crack size (limit load analysis) L cr3 Critical crack size for Case 3 L cr4 Critical crack size for Case 4 M 1 Safety margin for Case 1 M 2 Safety margin for Case 2 M 3 Safety margin for Case 3 M 4 Safety margin for Case 4 M Applied moment M 0 Reference moment calculated according to ref. [16] Fb Correction factor calculated according to ref. [16] H 1 Influence function calculated according to ref. [16] R Pipe mean radius t Pipe wall thickness θ Crack half-angle