General Papers
| Analysis of stress triaxiality influence: ferritic DCI damaging micromechanisms | |
| Vittorio Di Cocco, Francesco Iacoviello, Alessandra Rossi, Mauro Cavallini, Stefano Natali |
| Graphite nodule morphology evolution as an indicator of DCI macroscopic damage level | |
| Vittorio Di Cocco, Francesco Iacoviello, Alessandra Rossi, Daniela Iacoviello |
| Integrity and durability of photovoltaic modules: an overview of mechanical failure modes | |
| M. Paggi |
| Dog-bone versus Gaussian gigacycle fatigue specimens for size effect evaluation | |
| A. Tridello, D.S. Paolino, G. Chiandussi, M. Rossetto |
| Damage investigation of Zn-Al alloy coatings on steel wires | |
| L. Zortea, V. Volpe, S. Natali, V. Di Cocco, F. Iacoviello |
| Fretting damage parameters in splined couplings | |
| V. Cuffaro, F. Curà, A. Mura |
| Thermomechanical behaviour of alumina-mullite refractories developed by recycling industrial ceramic wastes | |
| A. Coglitore, A. Brentari, E. Burresi, F. Mazzanti, C. Mingazzini, M. Villa |
| Measurement of ductile fracture evolution in sheet metal forming | |
| M. Sasso, M. M. Rossi, G. Chiappini, D. Amodio |
| Effect of isothermal heat treatments on Duplex Stainless Steels impact toughness | |
| I. Calliari, M. Breda, E. Ramous, M. Magrini, G. Straffelini |
| Fracture behaviour of cast TiAl based intermetallic alloys | |
| A. Brotzu, F. Felli, D. Pilone |
| Simulation of fatigue debonding in adhesively bonded threedimensional joint geometries using a cohesive zone model approach | |
| F. Moroni, A. Pirondi, G. Giuliese |
| Fatigue damage evaluation of martensitic stainless steel by means of thermal methods | |
| U. Galietti, D. Palumbo, R. De Finis, F. Ancona |
| Shakedown in brittle-matrix fiber-reinforced cracked composite beams | |
| Andrea Spagnoli, Andrea Carpinteri, Lorenzo Montanari |
| Realization of a bone-inspired composite by means of a biomimetic approach | |
| F. Libonati |
| Strength and fracture of TWIP steel dissimilar weld joints | |
| P. Russo Spena, P. Matteis, A. Sanchez, G. Scavino |
| Hydrogen effects on fatigue strength of a High Strength Low Alloy steel | |
| L. Bertini, G. Lovicu, C. Santus, R. Valentini |
| Experimental determination of compressive strength of an unidirectional composite lamina: indirect estimate by Using Back-out Factor (BF) | |
| M. Scafè, M. Labanti, A. Coglitore, G. Raiteri, R. Dlacic, E. Troiani, E. Besseghini, M. P. Falaschetti |
| Martensitic phase transformation of Cu-Zn-Al alloy, induced by cold rolling deformation | |
| S. Natali, V. Volpe, L. Zortea, V. Di Cocco, F. Iacoviello |
| On the fatigue assessment of plain and short fibre/particle reinforced concretes | |
| Luca Susmel |
| Fracture mechanics parameters evaluation using the digital image correlation technique: a first approach | |
| G. La Rosa, A. Marino, Cugno Garrano |
| A numerical model to evaluate the effect of hydrogen embrittlement on low-alloy steels | |
| L. Vergani, G. Gobbi, C. Colombo |
| Experimental measure and model validation of COD of cracked pipes under bending | |
| D. Gentile, N. Bonora, G. Iannitti |
| Numerical-experimental analysis for residual stress determination in a welded joint | |
| G. Marannano, S. Allenza, A. Pasta, L. Fratini |
| Modeling of smart concrete beams with Shape Memory Alloy actuators | |
| S. Malagisi, E. Sacco, S. Marfia, J. Toti |
| Fatigue crack micromechanisms on a PE Zn-Cu-Al alloy | |
| Vittorio Di Cocco, Francesco Iacoviello, Stefano Natali, Valerio Volpe, Francesco Maiolino |
| Failure investigation on a helicopter main rotor actuator attachment | |
| L. Allegrucci, L. Aiello, A. Coletta, M. Bernabei |
| Very high-cycle fatigue resistance of shot peened high-strength aluminium alloys | |
| M. Benedetti, V. Fontanari, M. Bandini |
| Mechanical properties gradient in graphite nodules: influence on ferritic DCI damaging micromechanisms | |
| Vittorio Di Cocco, Francesco Iacoviello, Alessandra Rossi, Mauro Cavallini, Stefano Natali, Fanny Ecarla |
| Mechanical characterization of basalt fibre reinforced plastic with different fabric reinforcements – Tensile tests and FE-calculations with representative volume elements (RVEs) | |
| Piergiorgio Valentino, Franco Furgiuele, Marco Romano, Ingo Ehrlich, Norbert Gebbeken |
| Hot workability of aluminum particulate composites | |
| Paola Leo, Emanuela Cerri, Hugh McQueen |
| Crack path in a Zn-Cu-Al PE alloy under uniaxial load | |
| Vittorio Di Cocco, Francesco Iacoviello, Luigi Tomassi, A. Rossi, Stefano Natali, Valerio Volpe |
| Effects of a lubricating aqueous gel on the operative life of Ni-Ti endodontic rotary instruments: preliminary investigation | |
| A. Brotzu, F. Felli, C. Lupi, E. Fantini, C. Vendittozzi |
| Full field displacement measurements of notched pseudoelastic specimens Misure a pieno campo degli spostamenti in prossimità di intagli in leghe pseudoelastiche | |
| L. Bruno, F. Furgiuele, C. Maletta |
| Influence of carbon nanotubes addition onto the mechanical properties of restoration mortars | |
| A. Lopez, G. Ferro, P. Jagadale, J.-M. Tulliani |
| Application of Digital Image Correlation for the effect of glass fibres on the strength and strain to failure of polyamide plastics | |
| V. Crupi, E. Guglielmino, G. Risitano, F. Tavilla |
| Morphological characteristics of aluminium foams produced by replication casting | |
| A. Boschetto, L. Bottini, F. Campana, L. Consorti, D. Pilone |
| Identification of contact regimes in mechanical components for the evaluation of fretting damage | |
| V. Cuffaro, F. Curà, F. Curà, A. Mura, A. Mura |
| Fracture behaviour of grain refined A356 cast aluminium alloy: tensile and Charpy impact specimens | |
| D. Casari, A. Fortini, M. Merlin |
| Application of the Virtual Fields Method to fracture mechanics | |
| M. Rossi, M. Fardmoshiri, M. Sasso, D. Amodio |
| Adhesion strength of adhesive bonded NiTi thin metal sheets | |
| A. Santoro, M. Alfano, C. Maletta, L. Bruno, S. Candamano |
| Creep crack initiation and growth in 12%Cr-steel turbine disks | |
| S. Foletti, A. Lo Conte, S. Salgarollo, F. Bassi, A. Riva |
| Complex damaging analysys: integrated approach among fractography and other disciplines of evaluation and investigation | |
| A. Scanavini, F. Papazzoni, D. Cassinera |
| A potential-based particle method for failure modeling in solids | |
| Roberto Brighenti, Nicholas Corbari, Andrea Carpinteri |
| Microstructure and mechanical characterization of HVOF CoCrAlTa base coatings with different reinforcements | |
| E. Cerri, P. Leo, G.P. Zanon |
| Experimental method for the determination of the under-stress first-plasticization process parameters | |
| A. Risitano, G. Fargione |
| Toughening of silicon carbide-based materials | |
| G. Magnani, A. Brentari, S. Galvagno, G. Sico |
| Weight function for corner crack nearby intersecting cylindrical holes Funzioni peso per cricche ad angolo in corrispondenza di intersezione di fori | |
| E. Salvati, P. Livieri, R. Tovo |
| The specific heat loss combined with the thermoelastic effect for an experimental analysis of the mean stress influence on axial fatigue of stainless steel plain specimens | |
| G. Meneghetti, M. Ricotta, L. Negrisolo, B. Atzori |
| Interpolation model of fatigue crack propagation data | |
| M. Grasso, F. Penta, P. Pinto, G.P. Pucillo |
| Mixed mode fatigue crack growth in railway axles | |
| Marzio Grasso |
| FEM-DBEM coupled procedure for assessment of cracks in lateral supports of the magnet system of Wendelstein 7-X | |
| R. Citarella, M. Lepore, Joris Fellinger, Victor Bykov, Felix Schauer |
| Fatigue endurance of new high-strength car-body steels | |
| P. Matteis, G. Scavino, D. Firrao, R. Sesana, F. D’Aiuto |